  
 
|
Smart Turner
Pumps offices
or distributors
are located
throughout the
world, to serve
your pumping
needs. |
|
|
|
Non Clog, Horizontal Features
Casings:
A radially split, cast volute with separate suction cover, and 125/150 p.s.i. ANSI  ruggedly designed with generous allowance for abrasion and corrosion.
Impeller: A one piece casting,
the fully shrouded, enclosed impeller will handle solids of 3 inch diameter, or larger for some models. The impeller is machined, balanced, and trimmed to meet the exact performance requirements, and
the clearance between it and the suction cover is factory set. The impeller is keyed to the shaft and secured by a flow contoured washer and capscrew.
Wear Rings:
Either or both, impeller and suction cover can be fitted with renewable, axial clearance wear rings.
Stuffing Box Cover: A heavy one piece casting with rabbeted flange for
positive alignment. The deep bore will accept packing with a lantern ring, and single or double mechanical seals.
Gland: Split for packed stuffing boxes and solid for mechanical seals,
the gland is provided in a variety of arrangements to suit the application.
Shaft: Precision machined high quality alloy, normally fitted with a
renewable sleeve, the shaft is sized to minimize deflection to ensure smooth operation and maximum packing of seal life.
Bearings:
The grease lubricated, antifriction bearings are generously sized for long life, and are protected from moisture and dirt by seals in both bearing covers.
Bearing Housing:
The rigid cast iron bearing housing is spigot fitted to the stuffing box cover and supported by a heavy cast iron foot.
Handhole: The casing is provided with an inspection or cleanout
handhole with fully flow contoured, bolted, and gasketed cover.
Back Pull Out: Full casing mount with substantial integral casing feet
enables the bearing housing and impeller to be removed without disturbing either suction or discharge piping.
Discharge: Centreline discharge nozzle means only one rotation is required.
Tests: All pumps are hydrostatically tested to 50 p.s.i. above the maximum casing design pressure. |
Non Clog, Vertical Frame Mounted Drive Features
Casings:
A radially split, cast volute with separate suction cover, and 125/150 p.s.i. ANSI flat faced flanged connections, ruggedly designed with generous allowance for abrasion and corrosion.
Impeller: A one piece casting, the fully shrouded, enclosed impeller will handle solids of 3 inch diameter, or larger for some models. The impeller is
machined, balanced, and trimmed to meet the exact performance requirements, and the clearance between it and the suction cover is factory set. The impeller is keyed to the shaft and secured by a flow
contoured washer and capscrew.
Wear Rings: Either or both, impeller and suction cover can be fitted with renewable, axial clearance wear rings.
Stuffing Box Cover:
A heavy one piece casting with rabbeted flanged for positive alignment. The deep bore will accept packing with a lantern ring, and single or double mechanical seals.
Gland:
Split for packed stuffing boxes and solid for mechanical seals, the gland is provided in a variety of arrangements to suit the application.
Shaft:
Precision machined high quality alloy, normally fitted with a renewable sleeve, the shaft is sized to minimize deflection to ensure smooth operation and maximum packing of seal life.
Bearings: The grease lubricated, antifriction bearings are generously sized for long life, and protected from moisture and dirt by seals in both bearing covers.
Bearing Housing:
The rigid cast iron bearing housing is located above and spigot fitted to the stuffing box cover. The bearing housing accepts a 'C' flange motor for direct drive through a flexible coupling.
Suction Elbow: The pump suction is fitted with a 125/ 150 p.s.i. ANSI flat faced flanged cast elbow.
Handholes: Suction elbow and casing are both provided with inspection
or cleanout handholes with fully flow contoured, bolted, and gasketed covers.
Pump Stool: The entire pump is mounted on a substantial, cast, four
legged stool capable of supporting the full weight and torque of the pump and motor.
Discharge: Centreline discharge nozzle means only one rotation is
required. The discharge can be located at any one of eight positions.
Tests: All pumps are hydrostatically tested to 50 p.s.i. above the maximum casing design pressure.
|
|
